LP-33 Series Bridge Type Vertical Machining Center :
| Print this page | LP-4033 | LP-5033 | LP-6033 | LP-7033 |
|---|---|---|---|---|
| CAPACITY | ||||
| X-axis travel | 4,000 mm | 5,000 mm | 6,000 mm | 7,000 mm |
| Y-axis travel | 3,300 mm ( 4,000 mm Opt. ) | |||
| Z-axis travel | 760 mm ( 1,000 / 1,200 / 1,400 mm Opt. ) | |||
| Dist. form spindle nose to table top | 240 ~ 1,000 mm ( 200 ~ 1,200 mm / 200 ~ 1,400 mm / 200 ~ 1,600 mm Opt. ) | |||
| Dist. between columns | 3,500 mm | |||
| WORKING TABLE | ||||
| Table size ( X direction ) | 4,020 mm | 5,020 mm | 6,020 mm | 7,020 mm |
| Table size ( Y direction ) | 2,400 mm | |||
| Table load capacity | 15,000 kg | 18,000 kg | 20,000 kg | 20,000 kg |
| SPINDLE | ||||
| Spindle motor ( cont. / 30 min. ) | 22 / 26 kW ( 30 / 35 HP ) | |||
| Spindle speed | 6,000 rpm ( Std. ) Z-axis : 1,000 / 1,200 / 1,400 mm ; Gear 4,000 / 5,000 rpm ( Opt. ) Built-in 6,000 / 8,000 rpm ( Opt. ) Direct Drive 8,000 / 10,000 rpm ( Opt. ) |
|||
| Spindle taper | BT50 ( ISO50 ) / DIN69871-A ( Opt. ) | |||
| FEED RATE | ||||
| X-axis rapid feedrate | 15,000 mm/min. | 10,000 mm/min. | 10,000 mm/min. | 7,500 mm/min. |
| Y-axis rapid feedrate | 15,000 mm/min. | |||
| Z-axis rapid feedrate | 15,000 mm/min. | |||
| Cutting feedrate | 1 ~ 10,000 mm/min. |
1 ~ 5,000 mm/min. | ||
| TOOL MAGAZINE | ||||
| Tool magazine capacity | 32 ( 60 / 90 / 120 Opt. ) | |||
| Max. tool diameter / adj. pocket empty | Ø 127 / Ø 215 mm | |||
| Max. tool length ( from gauge line ) | 350 mm | |||
| Max. tool weight | 20 kg | |||
| Accuracy *1 | ||||
| Positioning accuracy ( JIS B 6338 ) | ± 0.015 mm / Full Travel | ± 0.010 mm / Full Travel |
||
| Positioning accuracy ( VDI 3441 ) | P ≤ 0.030 mm / Full Travel |
P ≤ 0.040 mm / Full Travel |
P ≤ 0.050 mm / Full Travel |
P = 0.040 mm / Full Travel |
| Repeatability ( JIS B 6338 ) | ± 0.003 mm | |||
| Repeatability ( VDI 3441 ) | Ps ≤ 0.025 mm | Ps ≤ 0.030 mm | Ps ≤ 0.035 mm | Ps = 0.030 mm |
| GENERAL | ||||
| Power requirement | 220 ± 10 % | |||
| Pneumatic pressure requirement ( min. ) | 5 ~ 8 ( 5 ) kg / cm² | |||
| Hydraulic unit tank capacity ( pump ) | 120 liter ( 10 HP ) | |||
| Lubrication oil tank capacity | 6 liter | |||
| Coolant tank capacity ( pump ) | 750 liter ( 1.5 HP ) | |||
| Machine weight | 45,000 kg | 49,000 kg | 57,000 kg | 66,000 kg |
Specifications are subject to change without notice.
1* X-axis travel more than 7,000 mm (inclusive) with the X-axis linear scale. ( Standrad Accessory )
Top